ECS Register Deltas vs OCS

This file documents registers that are new or changed in ECS versus OCS. OCS registers not listed here are unchanged.

New Registers

BEAMCON0 — $DFF1DC (ECS only)

The most significant new ECS register. Controls display sync generation and timing mode.

bit 15: HARDDIS  — disable hard limits on display window
bit 14: LPENDIS  — disable light pen latch
bit 13: VARVBEN  — enable variable VBlank
bit 12: LOLDIS   — disable long line sync
bit 11: CSCBEN   — composite sync on color burst
bit 10: VARVSYEN — variable vertical sync
bit  9: VARHSYEN — variable horizontal sync
bit  8: VARBEAMEN— variable beam enable
bit  7: DUAL     — dual sync (separate composite + RGB)
bit  6: PAL      — 1 = PAL timing, 0 = NTSC timing
bit  5: VARCSYEN — variable composite sync
bit  4: BLANKEN  — enable blanking signal
bit  3: CSYTRUE  — composite sync polarity
bit  2: VSYTRUE  — vertical sync polarity
bit  1: HSYTRUE  — horizontal sync polarity
bit  0: MONCSYEN — monochrome composite sync enable

Default OCS behavior is replicated by writing $0000 to BEAMCON0 on ECS.

PAL/NTSC software switch:

move.w  #$0020, $DFF1DC    ; BEAMCON0 = PAL mode
move.w  #$0000, $DFF1DC    ; BEAMCON0 = NTSC mode

Productivity mode (31 kHz):

move.w  #$0A00, $DFF1DC    ; VARBEAMEN + VARVSYEN (31 kHz VGA-like)

BPLCON3 — $DFF106 (ECS Denise only)

New bitplane/sprite control register — see chipset_ecs.md for full bit definition.

DENISEID — $DFF07C (read only, ECS+)

Chip identification — see chipset_ecs.md.

Changed / Extended Registers

BPLCON0 — $DFF100

OCS BPLCON0 bit 0 (ECSENA) is reserved (must be 0) on OCS. On ECS:

bit 0: ECSENA — 1 = enable ECS features (required to use BPLCON3 etc.)

Must set ECSENA=1 before programming ECS-specific display modes.

DIWSTRT / DIWSTOP — $DFF08E / $DFF090

OCS: 8-bit vertical and 8-bit horizontal (limited range).

ECS: DIWHIGH ($DFF1E4) extends these to full 12-bit resolution:

DIWHIGH — $DFF1E4 (ECS only)

bit 15:   FLOP1  — playfield 1 window high bit
bit 7:    FLOP0  — playfield 0 window high bit
bit 13-8: HB7-2  — horizontal window stop bits [7:2]
bit 5-0:  HS7-2  — horizontal window start bits [7:2]

Allows the display window to be positioned anywhere in the extended beam range, enabling full overscan without copper tricks.

FMODE — $DFF1FC (ECS read, AGA write)

On ECS, $DFF1FC is reserved. On AGA it becomes the FMODE register (see AGA section).

ECS-Only DMA Extended Mode

Super Agnus extends the chip bus to allow DMA access across the full 2 MB range. No register change is needed — the chip detects the extended address automatically based on the installed RAM size and its internal revision.

Programming Notes

Warning

OCS compatibility: Never write to BEAMCON0, BPLCON3, or DIWHIGH on OCS hardware — the addresses are not decoded on OCS and writes may corrupt adjacent chip state or have undefined effects. Always check GfxBase->ChipRevBits0 before writing ECS registers.

Safe ECS register programming pattern:

#include <graphics/gfxbase.h>

extern struct GfxBase *GfxBase;

void set_pal_mode(void) {
    if (GfxBase->ChipRevBits0 & (1 << GFXB_HR_AGNUS)) {
        /* Safe to write BEAMCON0 */
        volatile UWORD *beamcon0 = (UWORD *)0xDFF1DC;
        *beamcon0 = 0x0020;  /* PAL */
    }
}

References

ADCD 2.1 Hardware Manual — ECS register descriptions
NDK39: hardware/custom.h (note: some ECS registers not in OCS struct)
AmigaMail Vol. 2 — ECS programming tutorials
Amiga Hardware Reference Manual 3rd ed. — Appendix F

3.8 KiB Raw Blame History